2D-LC Dashboard Panel

Module Graphic

	Shows the status of the parking decks. The display is updated as cuts are parked or analyzed: Blue sidebar with down-arrow: deck is in the first dimension, a cut is being parked Deck A blue: 2D-LC valve in position 1 Deck B blue: 2D-LC valve in position 2 Red sidebar with up-arrow: deck is in the second dimension, a cut is being analyzed Deck A red: 2D-LC valve in position 2 Deck B red: 2D-LC valve in position 1 When Bypass is displayed, the solvent is flowing through the capillary, but the deck is not being used for parking, analysis or flushing. When there are no parking decks, the labels are Loop A and Loop B.
	When the solvent level falls below the specified volume, the yellow warning is shown; when the bottle is empty, the red error is shown. Clicking on the solvent bottle displays the Bottle Fillings dialog box. The tooltip for the bottle shows the solvent name.
	Indicates the presence of a solvent selection valve. Use the context menu to switch the valve.
	The pressure setpoints. The red line shows the current maximum pressure limit; the gray area shows the current pressure (also shown as text).

Actuals

The following pump actuals are displayed:

Flow	The current solvent flow rate (in mL/min).
Pressure	The current pump pressure (in bar or psi).
Pressure Limit	The current maximum pressure limit.
Composition A, B	The percentage contribution of each of the solvent channels to the current solvent composition. When a solvent selection valve is fitted, the channels are shown in the graphic.
Prepare Pump	Displays the current pump preparation operation and the run time for Prime.
Diverter Valve Position	Shows the current position of the diverter valve. This item is present only when a diverter valve is configured.
ASM Valve Position	Shows the current position of the ASM valve.
Deck A/B Valve Position	Shows the current position of the parking deck valves. These items are present only when parking deck valves are configured.
Tuning <Channel>	Indicates the tuning efforts of 1290 Infinity pumps. For pumps operating as expected, the signal should stay in a range of -1 to +1 within the full scale of -2 to +2.

Context Menu

The context menu contains the following commands:

Control	Displays the pump's Control dialog box.
Method	Displays the pump's Method Setup dialog box.
Error Method	Set Error Method Sets the error method to the method that is currently available in the hardware. The error methods are loaded automatically on all modules if an error occurs. Clear Error Method Removes the currently loaded error method.
Identify	Displays a list of devices to identify. The LED on the front of the selected module blinks for a few seconds.
Switch On/Off	Toggles the status of the pump, on or off.
Switch Solvent Selection Valve A/B	Switches the solvent selection valve to the alternative position. These menu items are present only when a solvent selection valve is configured.
Bottle Fillings	Displays the Bottle Fillings dialog box.
Prepare Pump	Displays the Prepare Pump dialog box. (G7120A and G4220A)
Seal Wash Prime	Allows you to ensure that all air bubbles in the seal wash lines are removed (for example, after the seal wash solvent bottle has been refilled). (G7120A only)
Switch Valve	Select the valve to switch from the submenu Switch Diverter Valve Toggles the diverter valve between Position 1 and Position 2. This item is shown only when a diverter valve is configured. Switch 2D-LC Valve Toggles the 2D-LC valve between Position 1 and Position 2. This item is shown only when a 2D-LC valve is configured. Switch ASM Valve Displays the Switch ASM valve position dialog box, which allows you to switch the ASM valve to a different position. Switch Deck A/B Valve Displays the Switch Deck A/B valve position dialog box, which allows you to switch the selected parking deck valve to a different position.
Modify	Select what to modify from the submenu: Capillaries Displays the Modify Capillaries dialog box, which allows you to change the capillary configuration. Transfer Volumes Displays the Modify Transfer Volumes dialog box, which allows you to change the transfer volumes.